EDGE PRODUCTS 98920 EAS REPLACEMENT 15" EGT LEAD FOR EAS 98620 CS2/CTS2/CTS3

The EDGE PRODUCTS 98920 EAS Replacement 15" EGT Lead is the direct replacement thermocouple and lead for the popular EDGE PRODUCTS 98620 EAS EGT Starter Kit. If your original EGT probe or cable has been damaged, this 15" lead restores accurate exhaust gas temperature monitoring so you can safely tow, tune, and daily drive your diesel without guessing at EGTs. edge products 98920 eas replacement 15 inch egt lead, edge 98920 diesel egt thermocouple for 98620, edge cs2 cts2 cts3 replacement egt sensor cable, cpp diesel edge products eas accessories, exhaust gas temperature probe for edge insight cts3

Designed for the Edge EAS (Expandable Accessory System), the 98920 plugs in seamlessly to your existing EAS harness and CS2/CTS2/CTS3 monitor. No splicing, no guesswork. Just remove the failed probe/lead from your 98620 kit and install this new unit to get reliable EGT data back on-screen. edge eas replacement egt lead kit, edge products 98920 for edge 98620 daily driver tow kit, diesel towing egt monitoring upgrade, cppdiesel edge insight cts3 egt solution

Key Features & Benefits

• Direct replacement for the EGT probe/lead supplied with Edge EAS EGT Kit PN 98620.
• 15" thermocouple lead for clean routing from manifold to harness.
• Plug-and-play Edge EAS connector – no cutting, soldering, or adapters required.
• Compatible with Edge CS2, CTS2, and CTS3 monitors when used with an EAS EGT kit.
• Accurate exhaust gas temperature feedback to help prevent over-temp damage under load.
• Ideal for tuned and towing diesels that regularly see elevated EGTs.

Fitment & Compatibility

The EDGE PRODUCTS 98920 is not a universal gauge probe – it is specifically engineered as a replacement for the EGT probe/lead included with the Edge EAS EGT Kit (PN 98620). If your truck already has:

• An Edge CS2, CTS2, or CTS3 Insight or Juice w/ Attitude monitor, and
• An installed Edge EAS EGT Kit PN 98620,

then 98920 is the correct replacement lead.

Because the EAS system is vehicle-agnostic, this replacement EGT lead can be used on virtually any OBD-II diesel pickup where an Edge monitor and EAS 98620 kit are supported, including but not limited to:

• 1989+ Dodge/Ram Cummins trucks equipped with Edge CS2/CTS2/CTS3 & EAS EGT Kit.
• 1994+ Ford Power Stroke trucks running Edge Insight/CTS/CTS3 & EAS EGT Kit.
• 2001+ GM Duramax trucks using Edge Insight CTS/CTS2/CTS3 & EAS EGT Kit.

Important: This part does not include a complete starter kit or EAS cable harness. It is intended to replace a worn or damaged probe/lead from an existing Edge 98620 EGT kit.

Cross-Reference & Related EDGE PRODUCTS at CPP DIESEL

Build a complete, reliable monitoring setup by pairing the 98920 EGT replacement lead with these EDGE PRODUCTS already available at CPP Diesel:

• EDGE PRODUCTS 98620 EAS EGT STARTER KIT DAILY DRIVER/TOW KIT COMPATIBLE W/ CS2/CTS2/CTS3 – the original kit that includes the EAS starter cable and EGT probe your 98920 replaces.
• EDGE PRODUCTS 98611 EAS EGT W/OUT START KIT COMPATIBLE W/ CS2/CTS2/CTS3 – expandable EGT kit for trucks that already have an EAS starter cable installed.
• EDGE PRODUCTS 98106 EAS OBDII PASS THROUGH SPLITTER FOR 96-UP OBD II COMPLIANT VEHICLES – lets you run your Edge monitor and another OBD-II device at the same time.

Installation Notes

• Manifold must be drilled and tapped (typically 1/8" NPT) for the thermocouple if not already done.
• Route the 15" lead away from direct turbine and downpipe heat, sharp edges, and moving components.
• Plug the connector into your existing EAS EGT harness and confirm EGT readings on your Edge monitor.

Specifications

Specifications for EDGE PRODUCTS 98920

Frequently Asked Questions