BDS SUSPENSION BDS761FPE 3" UCA LIFT KIT WITH FOX 2.5 PERFORMANCE ELITE SHOCKS 2020-2024 GM SILVERADO/SIERRA 2500HD/3500HD 4WD

Upgrade the handling and performance in your GM Silverado/Sierra 2500HD/3500HD 4WD with the BDS Suspension 3" UCA Lift Kit With Fox 2.5 Performance Elite Shocks. Designed for a simple bolt-on installation, these kits allow clearance for up to 35" tires. At the heart of this new system is a pair of heavy-duty tubular upper control arms (UCAs) designed for improved strength and suspension travel. These new control arms are built from thick wall 1.5" DOM tubing and use an indexed ball joint cup to reposition the upper ball joints to allow more droop travel. These arms come fully assembled right out of the box with high-quality greaseable ball joints and rubber bushings for long life, quiet operation, and superior corrosion resistance over uni-balls and heims. Along with the control arms, a pair of indexed cast steel torsion bar keys are supplied up front to lift vehicle. A small differential relocation kit is supplied to correct CV axle operating angles without effecting ground clearance. To eliminate sway bar interference, a pair of sway bar relocation brackets is used which maintains proper operating angle.

In the rear, a 2" block and U-bolt kit are used to create a level to slightly tail high stance when unloaded. The biggest upgrade in this kit is FOX 2.5 Performance Elite Series shocks at each corner. These large aluminum-bodied shocks feature DSC (Dual Speed Compression) adjustable reservoirs for additional damping capacity, better heat dispersion, and tunable ride. This system utilizes next level damper performance for smooth on-road comfort and extreme off-road capability allowing you to push your truck harder.

All BDS Suspension lift kits come with the security of knowing you purchased the finest lift kit in the aftermarket suspension industry. They back their commitment to manufacturing reliable, high-quality suspension products with their unique "No BS Hardcore Lifetime Warranty".

FEATURES:

• 3" UCA Lift Kit

• 2" Rear Blocks

• Sway Bar Relocation Brackets

• Indexed Cast Steel Torsion Bar Keys

• Front Differential Relocation Bracket

• Heavy-Duty Tubular Upper Control Arms

• Covered By The BDS "No Fine Print" Warranty

• FOX 2.5 Performance Elite Series Shocks (Front & Rear)

SUGGESTED WHEEL & TIRE COMBINATIONS

35X12.50 W/20X9 And 5.5-5.75" Back Spacing

295/60 W/20X9 And 5-5.75" Back Spacing

285/65 W/20X9 And 5-6.18" Back Spacing

*trimming may be required

IN THE BOX

BDS761FPE

With Overload Springs

KIT NOTES:

Disassembly/assembly of the factory torsion bar system requires the use of a special unloading tool. The GM specified tool #CH48809

Compatible with gas or diesel models

Compatible with AT4 models

Some minor trimming may be necessary to fit certain wheel/tire combination. This is normal with most aftermarket tire/wheel fitment on Chevy/GM trucks and typically consists of trimming the bottom edge of the inner fender shrouds and/or lower corner of front bumper valance. As a rule of thumb, deeper backspacing and shorter/ narrower tires will reduce/eliminate trimming required. Further trimming tips are included at the end of this instruction sheet

KIT CONTENTS:

(1) BDS011217 - 11-23 Chevy HD 2" Rear Block w/ ovrld

(1) BDS011310 - 2020+ GM 2500/3500 3" Box Kit

(1) FOX88326084 - Kit: 20-ON GM 2500/3500 w/ UCA, Front, 2.5 Truck PES, R/R, 5.7", 1.5-2.5" Lift, DSC

(1) FOX88326085 - Kit: 20-ON GM 2500/3500, Rear, 2.5 Truck PES, P/B, 10.17", 0-1" Lift, DSC

VEHICLE FITMENT