BANKS 42790 MONSTER-RAM INTAKE ELBOW KIT W/FUEL LINE AND HUMP HOSE 4 INCH NATURAL FOR 07.5-18 CUMMINS 6.7L 24V

4-inch CNC machined inlet. Four 1/8-inch NPT ports designed for optimal atomization of water-methanol or NOS. Accommodates stock mounting points. Optimizes air pressure and distribution into the intake manifold. Includes proprietary #1 fuel line, 4 to 3.5-inch hump hose, and all necessary hardware. Not emissions compliant.

The Monster-Ram improves airflow from the intercooler and flows 1008 cfm (77.01 lbs/min) compared to Stock's measly 432 cfm (33.00 lbs/min). It raises boost without increasing backpressure at the turbine which results in a more responsive and power efficient engine. Up to four 1/8 inch NPT ports are pre drilled to measure pressure, temperature, or flow. The top two NPT ports are positioned to allow for proper atomization directly into the center of the air mass. Accommodates stock mounting points including Temperature and Pressure sensors, wire harness, and dipstick tube.

At Banks Power, just enough is never enough when it comes to engine airflow. Maximum power, performance, and efficiency are the ultimate goals. To make it all happen the engine has to breathe freely and without needless restrictions. Finding ways to pump your engine full of cooler, denser air has always been the key.

Our High-Ram intakes have always whipped the competition. Our new Monster-Ram flat-out destroys it. Monster ram is CNC ported to a full 4.0 inch and was designed utilizing the latest in electronic computational fluid-dynamic technology. Next it was tested on the flow bench and dyno, then finally proven in the real world where the rubber meets the road. The Monster-Ram is a beast that only Banks could have unleashed. A simple, direct-replacement casting, Monster-Ram is instant power, performance, and acceleration gratification.

It's the perfect upgrade whether you're just starting out or working to build a serious, purpose-built race machine.

Key Features

• Four 1/8 inch NPT ports (Top ports targeted for optimal atomization of Straight-Shot water-methanol)
• Includes fuel line, 4 to 3.5-inch hump hose, and all necessary hardware
• Optimizes air pressure and distribution going into the intake manifold
• Raises boost without increasing turbine drive pressure
• Includes Fuel Line and all necessary hardware
• Improves flow of oxygen-rich air into cylinders
• Larger and less restrictive than stock intake
• Accommodates stock mounting points
• Outflows stock over 110-133 percent
• 4.0 inch CNC machined inlet
• Natural Bare Finish

The BANKS 42790 Monster-Ram Intake Elbow Kit is a powerhouse upgrade designed to revolutionize your 2007.5-2018 Cummins 6.7L 24V engine. Featuring a 4-inch CNC machined inlet, this intake elbow kit is engineered for optimal performance. The inclusion of four 1/8-inch NPT ports allows for precise atomization of water-methanol or NOS, elevating your engine's capabilities to the next level.

With the Monster-Ram, airflow is significantly enhanced, boasting an impressive 1008 cfm (77.01 lbs./min) compared to the stock's 432 cfm (33.00 lbs./min). This increase in airflow translates to heightened boost levels without adding backpressure, resulting in a more responsive and power-efficient engine. The predrilled 1/8-inch NPT ports offer flexibility for measuring pressure, temperature, or flow, ensuring optimal performance customization.

Designed to accommodate stock mounting points, including sensors, wire harness, and dipstick tube, the Monster-Ram optimizes air pressure and distribution into the intake manifold, promoting maximum power and efficiency. The kit includes a proprietary fuel line, a 4 to 3.5-inch hump hose, and all necessary hardware for a seamless installation experience.

From the industry leader, Banks Power, the Monster-Ram sets a new standard in performance upgrades. Utilizing advanced computational fluid-dynamic technology, this intake elbow is CNC ported to 4.0 inches for unrestricted airflow. Backed by rigorous testing on flow benches and dyno runs, the Monster-Ram guarantees instant power, performance, and acceleration gains.

Unleash the full potential of your Cummins engine with the BANKS 42790 Monster-Ram Intake Elbow Kit. Whether you're a novice enthusiast or a seasoned racer, this quality upgrade promises to deliver unparalleled results that exceed expectations. Note that this product is not emissions compliant and is intended for race use only, requiring the removal of emissions equipment for optimal performance. For an unmatched driving experience, equip your engine with the Monster-Ram and experience the difference in power and efficiency firsthand.