BD DIESEL
BD DIESEL VENOM DUAL CP3 INSTALL KIT W/ CONTROLLER 05-09 CUMMINS - 1050486
- SKU:
- BDD1050486
- MPN:
- 1050486
- Shipping:
- Calculated at Checkout
Description
BD Diesel 1050486 Venom Dual CP3 Install Kit with Controller for 2005-2009 CUMMINS 5.9L/6.7L 24V turbo diesel engines is the ultimate solution for those seeking unrivaled fuel supply capabilities. Whether you're aiming for peak performance or just looking to enhance your vehicle's power, this kit has you covered.
Designed to fuel power-hungry rigs, the BD Venom Dual CP3 Kit is your ticket to achieving horsepower feats of up to 1800hp with R900 12mm Stroker pumps. Even with two stock pumps, it can supply enough fuel for over 1000hp, ensuring a potent performance boost for your truck.
What makes this kit stand out is its comprehensive inclusions. With high-quality molded silicone radiator hose, factory connector harness, and a low-profile bracket, installation is a breeze and cost-effective. The low-profile CP3 pump location also allows for aftermarket intake horns, further boosting your vehicle's capabilities.
The optional CP3 pump control module makes managing the dual pump setup seamless, splitting the ECM signal with no additional tuning needed. Plus, the quick installation process clocks in at just 2 hours and 30 minutes, getting you back on the road swiftly.
With a 12-month parts warranty, you can trust in the quality and durability of this kit. However, please note that ECM tuning is necessary, and this product is not intended for use on licensed California vehicles.
EPA-approved and meeting reasonable basis requirements, the BD Diesel 1050486 Venom Dual CP3 Kit with Controller ensures compliance while unleashing your CUMMINS engine's full potential. Upgrade your fuel system with this top-of-the-line kit and experience the power of dual pumps – because two is always better than one!
View AllClose
Designed to fuel power-hungry rigs, the BD Venom Dual CP3 Kit is your ticket to achieving horsepower feats of up to 1800hp with R900 12mm Stroker pumps. Even with two stock pumps, it can supply enough fuel for over 1000hp, ensuring a potent performance boost for your truck.
What makes this kit stand out is its comprehensive inclusions. With high-quality molded silicone radiator hose, factory connector harness, and a low-profile bracket, installation is a breeze and cost-effective. The low-profile CP3 pump location also allows for aftermarket intake horns, further boosting your vehicle's capabilities.
The optional CP3 pump control module makes managing the dual pump setup seamless, splitting the ECM signal with no additional tuning needed. Plus, the quick installation process clocks in at just 2 hours and 30 minutes, getting you back on the road swiftly.
With a 12-month parts warranty, you can trust in the quality and durability of this kit. However, please note that ECM tuning is necessary, and this product is not intended for use on licensed California vehicles.
EPA-approved and meeting reasonable basis requirements, the BD Diesel 1050486 Venom Dual CP3 Kit with Controller ensures compliance while unleashing your CUMMINS engine's full potential. Upgrade your fuel system with this top-of-the-line kit and experience the power of dual pumps – because two is always better than one!
BD's Venom Dual CP3 Kits for Dodge 5.9L/6.7L Cummins engines are capable of supplying enough fuel for 1000hp with 2 stock pumps, and over 1800hp with R900 12mm Stroker pumps! Kit includes everything you need for a low cost, quick install including high quality molded silicone radiator hose, harness with factory connectors, and a low-profile bracket. The kit is designed for use with a Duramax model CP3 pump, and can be purchased with or without a CP3 pump. Lower profile location of CP3 pump allows the install of aftermarket intake horns! Available with CP3 pump control module that splits the ECM signal to the two pumps, without any additional ECM tuning required.
FEATURES
- Capable of supplying enough fuel for over 1000hp with 2 stock pumps and 1800hp with two R900 12mm Stroker pumps
- Includes everything you need for a low cost, quick install including high quality silicone radiator hose
- Harness with factory connectors to plug-in both pumps
- Low profile bracket with included idler for better belt wrap on CP3 drive pulley
- Lower profile location of CP3 pump allows the install of aftermarket intake horns
- Designed for use with a Duramax model CP3 pump
- Available with or without second CP3 pump
- Optional CP3 controller plugs into both CP3 pumps and splits ECM signal - no additional tuning required
INSTALL TIME
- 2 Hours 30 Minutes
WARRANTY
Parts
- 12-Months
NOTE
- ECM turning required
- Not for sale on licensed California vehicles
EMISSIONS
- This product has met EPA's reasonable basis requirements and is legal for sale and use within the jurisdiction of the federal EPA. (EMS:2)